Vehicles
90 not categorized PORSCHE 944 SHIP FEECan't find what you need? Try browsing the Accessories or Exploded Diagrams!<-- Try narrowing by car using the menu to the left.91150195500GRV Front floor with suspension mounts. Galvanized primed painted. One of the most abused part of the 911 are the floor panels. Years of exposure to moisture, salt, sand, and mud often takes a toll on the metal under your feel. If your Porsche floors have seen better days and are showing the ugly signs of corrosion, we have replacement panels. Each one is painstakingly made to duplicate the factory pieces and galvanized for long life. View/Change Diagram
From $598.40
Make a selection 93034732200 If your outer tie rods are worn, you will experience sloppy steering response and knocking / creaking sounds. Your outer tie rods keep the steering centered, so failure can be dangerous and can seriously affect steering control. After replacing the tie rods, you will experience tighter, more precise feedback without noise. Tie rod end consists of: 1 qty. Ball joint end 1 qty. Dust bellows / boot 1 qty. Hexagon lock nut 1 qty. Lock nut washer 1 qty. Pin high-quality OEM (original equipment manufacturer) replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. We recommend replacing the right and left side tie rod ends at the same time....(choose a part on the right to read more) View/Change Diagram
From $13.95
Make a selection FVD116917 This sachs racing 4 puck disc with sintered metal plates and torsion springs has a higher friction coefficient than plates with organic friction material. That allows for higher transmittable torque (405 ft lb. / 550 nm max.) and makes them more dirt and oil resistant. This disc has an aggressive start performance (small clutch pedal release window) so is best suited for race use (endurance races, hill climbing, slalom and rally's). It is assembled by hand, which guarantees the highest quality attributes both in terms of clamping load and release characteristics. This disc is a rigid disc (un-sprung) and is purposefully built to be used with the original dual mass flywheel (dmfw) which includes dampers / sprin...(choose a part on the right to read more) General FitmentCAYMAN 2006-08BOXSTER 2005-08 BOXSTER 1997-04
From $598.67
Make a selection 96433307401S We specify that the manufacturer use a 25% more stiff grade of rubber known in the industry as 85 shore. 85 shore refers to the rubbers density or hardness value. Oem is 65 shore and the factory European rs models use 85 shore; it suffers from less deflection, maintains more precise alignment and gives you the same repetitive feeling corner after corner. With aircooled 911's going up so much in value these days, we wanted to create suspension parts that look 100% oem, but also offer sportier handling without being too stiff for street use. They are manufactured in europe by an OEM supplier using the finest materials available (high carbon steel, 7075 t6 aluminum and 85 shore rubber). Upgrade yours today! Sold ...(choose a part on the right to read more) General Fitment911 1989-94
$159.50
Make a selection 96460601900 This switch is feeds throttle information back to the dme. It tells the system if the throttle is idling or at wide open throttle. If you are experiencing an unstable idle this may be a contributing factor. Sold individually. 1 necessary per car. View/Change Diagram
$420.00
Make a selection 99334703104 If your outer tie rods are worn, you will experience sloppy steering response and knocking / creaking sounds. Your outer tie rods keep the steering centered, so failure can be dangerous and can seriously affect steering control. After replacing the tie rods, you will experience tighter, more precise feedback without noise. Tie rod consists of: 1 qty. Tie rod 1 qty. Hexagon nut (m14 x 1.5) 1 qty. Inner axial joint 1 qty. Lock nut 1 qty. Dust bellows / boot we recommend replacing the right and left side tie rods at the same time. Sold individually. 2 necessary per car.
$216.29
Make a selection 99731416600 The manual transmission turbo models use a hydraulic accumulator. If it is beginning to fail, you will experience a very heavy clutch pedal when the engine is not running. Once the car is started and begins to warm up the pedal becomes less heavy. You can also feel that the pedal is very notchy in certain spots. We always recommend replacing the accumulator when installing a new slave cylinder. Also, replace the accumulator o-ring, part # 99970722440 for 993 and 996 turbo and o-ring, part # 99970752940 for 997 and 997-2 turbo. Original part # for the 993 turbo was 993 314 166 00, it has been superseded since then. Sold individually. 1 necessary per car. View/Change Diagram
From $160.89
Make a selection 097100880009 The techart aero styling brand has become a leader in the premium automotive segment. Each part is precision designed and manufactured in Germany for perfect fitment and superior durability. Each part is wind tunnel tested and approved for added downforce to complement any performance upgrade. General Fitment911 TURBO/GT2 2007-09
$1,640.10
Make a selection FVD20798701 This oil pump is a must for vehicles driven on the track. The issue: the 987.1 Boxster/Cayman from 2005 to 2008 has the factory return oil pump located on the right rear side. On the left side, the return oil pump located in front. So when driven fast in right turns, the oil from the camshaft case (rear left) does not flow back quickly enough into the oil pan. When the oil pan is starved of oil, the oil pump sucks in air and over time the motor will seize. The solution: our tandem return oil pump draws oil from the camshaft housing in (rear left, 3rd cylinder) and feeds it back into the oil pan so that starvation is not created when cornering hard.
$2,744.50
Make a selection FVD33150005 Restore proper suspension geometry with this adjustable lower rear control arm. The factory control arm cannot compensate enough when lowering your Porsche, leaving you with as much as ½ inch of toe in. The result is poor handling and rapid tire wear. This kit will provide the additional adjustment needed. The adjusting link has a left and right hand thread on each end. Rotating the link will increase or decrease the overall length of the arm. A precision teflon lined spherical rod end replaces the compliant rubber factory bushing for improved suspension response and feedback, and also reduces toe changes during acceleration and deceleration. Sold in pairs. 1 necessary per car.
$764.50
Make a selection FVD34391192SET Replace worn-out original front lower control arm bushings with our FVD sport bushings, made of rubber with an 85 shore hardness value that is the same as the rs models. 85 shore is more durable, provides more positive suspension location and is still quiet and comfortable for street use. Features: better handling reduces that sloppy steering feel makes precision adjustments of the suspension easier does not produce any noise like the teflon bushings. Rubber has a shore hardness value of 85 (like rs models) fit's like oem, simple installation made in Germany set is sold per axle. 2 necessary per car.
$158.40
Make a selection FVD3511B18022A This line is dedicated to the most demanding customers. This braking system originates from the racing components, consisting of a ventilated, integral or composite disc, aluminum calipers, a complete set of high performance brake pads, TUV/dot homologated metal-braided brake hoses and high quality fastener hardware. Calipers are available in red, black or silver. Proven on-track performance; extraordinarily powerful and consistent under the repeated loads. Disperses gasses, cleans pads for better "bite". Reduces "un-sprung weight" at each corner for better handling. Provides maximum braking force without the flex of sliding calipers. Reduces heat-related stress, increases brake performance and pedal feel. ...(choose a part on the right to read more)
$5,959.21
Make a selection FVD3511G29016A This line is dedicated to the most demanding customers.this braking system originates from the racing components, consisting of a ventilated, integral or composite disc, aluminium calipers, a complete set of high performance brake pads, metal braid tubes and high quality small parts. Please remember that in the European community, gran turismo products may only be used in racing and on private roads, unless you have obtained a new approval in compliance with directive 98/12/ec. Proven on-track performance; disperses gasses, cleans pads for better 'bite'; reduces 'usprung weight' for better handling; provides maximum braking force without the flex of sliding callipers; reduces heat-related stress, increases ...(choose a part on the right to read more)
$6,409.13
Make a selection FVD3511M19004A The brembo gran turismo (gt) braking system is ideal for use on the street and for light track use. This GT system expands upon the original drilled disc's face type made by Porsche. The cross drilled disc surface continuously refreshes the braking surface and offers the highest initial response of any disc type. So, you can confidently respond to sudden pedestrian or traffic movement with maximum braking performance. Drilled discs operate in a wide range of operating temperatures and environments and respond confidently in wet weather. The GT line is dedicated to the most demanding customers. It originates from racing components, consisting of floating ventilated cross drilled discs, aluminum calipers with op...(choose a part on the right to read more)
$5,054.50
Make a selection FVD3511M29007A This line is dedicated to the most demanding customers.this braking system originates from the racing components, consisting of a ventilated, integral or composite disc, aluminium calipers, a complete set of high performance brake pads, metal braid tubes and high quality small parts. Please remember that in the European community, gran turismo products may only be used in racing and on private roads, unless you have obtained a new approval in compliance with directive 98/12/ec. Proven on-track performance; disperses gasses, cleans pads for better 'bite'; reduces 'usprung weight' for better handling; provides maximum braking force without the flex of sliding callipers; reduces heat-related stress, increases ...(choose a part on the right to read more)
$5,054.50
Make a selection FVD3511M39040A2 The brembo gran turismo (gt) braking system with type iii rotors is ideal for ideal for clubsport and sprint type track events. It utilizes brembo type iii aggressive face-type discs that offer high initial response with a smooth pedal feel. The type iii offers the highest overall braking confidence and control, allowing a quick qualifying time or top results in sprint races. The GT line is dedicated to the most demanding customers. It originates from racing components, consisting of floating ventilated cross drilled discs, aluminum calipers with opposed pistons, a complete set of high-performance brake pads, abrasion and corrosion resistant goodridge braided steel brake lines and high-quality fastener hardware...(choose a part on the right to read more)
$5,054.50
Make a selection FVD3511N29501A This line is dedicated to the most demanding customers.this braking system originates from the racing components, consisting of a ventilated, integral or composite disc, aluminium calipers, a complete set of high performance brake pads, metal braid tubes and high quality small parts. Please remember that in the European community, gran turismo products may only be used in racing and on private roads, unless you have obtained a new approval in compliance with directive 98/12/ec. Proven on-track performance; disperses gasses, cleans pads for better 'bite'; reduces 'usprung weight' for better handling; provides maximum braking force without the flex of sliding callipers; reduces heat-related stress, increases ...(choose a part on the right to read more)
$5,384.50
Make a selection FVD3511N29523A This line is dedicated to the most demanding customers.this braking system originates from the racing components, consisting of a ventilated, integral or composite disc, aluminium calipers, a complete set of high performance brake pads, metal braid tubes and high quality small parts. Please remember that in the European community, gran turismo products may only be used in racing and on private roads, unless you have obtained a new approval in compliance with directive 98/12/ec. Proven on-track performance; disperses gasses, cleans pads for better 'bite'; reduces 'usprung weight' for better handling; provides maximum braking force without the flex of sliding callipers; reduces heat-related stress, increases ...(choose a part on the right to read more)
$5,384.50
Make a selection FVD3522P18027A The brembo gran turismo (gt) braking system is ideal for use on the street and for light track use. This GT system expands upon the original drilled disc's face type made by Porsche. The cross drilled disc surface continuously refreshes the braking surface and offers the highest initial response of any disc type. So, you can confidently respond to sudden pedestrian or traffic movement with maximum braking performance. Drilled discs operate in a wide range of operating temperatures and environments and respond confidently in wet weather. The GT line is dedicated to the most demanding customers. It originates from racing components, consisting of floating ventilated cross drilled discs, aluminum calipers with op...(choose a part on the right to read more)
$4,064.50
Make a selection FVD3522P19005A Brembo's brake systems are designed to meet the the needs of the most demanding of customers. Brembo brake systems originate from racing components and offer proven on-track performance. Brembo high performance systems offer a significant reducuction in usprung weight for better handling and provides maximum braking force without the flex of sliding callipers. Brembo components reduce heat-related stress and increase brake performance for a better overall pedal feel with less fade. Brake kits come with aggressive pads that last longer than OEM and provide the highest level of performance. Brembo brake systems also consist of a ventilated, integral or composite brake disc, light weight aluminium calipers, steel...(choose a part on the right to read more)
$4,669.01
Make a selection FVD3522P19027A Brembo's brake systems are designed to meet the the needs of the most demanding of customers. Brembo brake systems originate from racing components and offer proven on-track performance. Brembo high performance systems offer a significant reducuction in usprung weight for better handling and provides maximum braking force without the flex of sliding callipers. Brembo components reduce heat-related stress and increase brake performance for a better overall pedal feel with less fade. Brake kits come with aggressive pads that last longer than OEM and provide the highest level of performance. Brembo brake systems also consist of a ventilated, integral or composite brake disc, light weight aluminium calipers, steel...(choose a part on the right to read more)
$4,174.50
Make a selection FVD3522P29024A Brembo's brake systems are designed to meet the the needs of the most demanding of customers. Brembo brake systems originate from racing components and offer proven on-track performance. Brembo high performance systems offer a significant reducuction in usprung weight for better handling and provides maximum braking force without the flex of sliding callipers. Brembo components reduce heat-related stress and increase brake performance for a better overall pedal feel with less fade. Brake kits come with aggressive pads that last longer than OEM and provide the highest level of performance. Brembo brake systems also consist of a ventilated, integral or composite brake disc, light weight aluminium calipers, steel...(choose a part on the right to read more)
$4,174.50
Make a selection FVD3522P38056A2 The brembo gran turismo (gt) braking system with type iii rotors is ideal for ideal for clubsport and sprint type track events. It utilizes brembo type iii aggressive face-type discs that offer high initial response with a smooth pedal feel. The type iii offers the highest overall braking confidence and control, allowing a quick qualifying time or top results in sprint races. The GT line is dedicated to the most demanding customers. It originates from racing components, consisting of floating ventilated cross drilled discs, aluminum calipers with opposed pistons, a complete set of high-performance brake pads, abrasion and corrosion resistant goodridge braided steel brake lines and high-quality fastener hardware...(choose a part on the right to read more)
$4,064.50
Make a selection FVD375002 This mount kit is a solid upgrade like the European super cup cars. They will provide you with a more responsive chassis and faster lap times with a tighter feel to the car. Note: you will experience more vibration and more noise with solid mounts. Be sure to check the fits these models tab as these do not fit every model.
$87.99
Make a selection FVD3522P38056AS The brembo gran turismo s (gt-s) braking system is ideal for clubsport and sprint type track events. The GT-s type iii system utilizes brembo type iii aggressive face type discs that offer high initial response with a smooth pedal feel. The type iii offers the highest overall braking confidence and control, allowing a quick qualifying time or top results in sprint races. Gt-s systems contain advanced calipers that include racing style radiators, dual inner piston seals, an inner pressure seal and an outer wiper seal. This innovative design provides the best combination of performance and long-lasting track use. The calipers are hard anodized in black (machined brembo logo in red) for resistance to corrosion and...(choose a part on the right to read more)
$4,174.50
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |